Home > Hot Tub > Hydro Spa Heater Not Working

Hydro Spa Heater Not Working

Contents

Watch Queue Queue __count__/__total__ SPA IS NOT HEATING John Powers SubscribeSubscribedUnsubscribe22 Loading... Loading... So Im thinking I need a new pressure switch. This Hydro Spa problem could be a temporary glitch occurring in the system. http://swusf.org/hot-tub/heater-not-working-in-hot-tub.html

Yes, the heater can be replaced. As mentioned above, it is usually one of these components that will cause a spa not to heat. Inside is the heating coil [13], a filament encased in insulating powder [11]. Pump Air Switch Blower Air Switch Time Clock Thermostat Contactor/Relay Pump Motor Ozonator 5 Continuous low speed. look at this web-site

Hot Tub Not Heating Up Enough

MORE CONTACTOR INFORMATION In order for a contactor to close it must have power to the coil, this power is usually traced through a series of components i.e., thermostat, hi-limit and Symptom Components Associated Cure 1 Spa does not run, no power, nothing works. Sign in here. This will prevent corrosion of heater parts by water which is too acidic (pH to low) and prevent heater scale buildup caused by pH too high.

A very high (or infinite) reading indicates a bad unit: open circuit or limited conductivity. The final thing it could be, without getting further complicated, is the hi-limit switch is faulty and needs to be replaced. Below are the most common contactor's and their coil placements. How To Reset Hot Tub Control Panel SwimUniversity 58,012 views 5:41 How to Fix an Air Lock in Your Spa : Pools & Spas - Duration: 3:08.

Working... Hot Tub Won't Heat Up A tub won't send voltage to the element if the pressure switch doesn't detect flow. spa is set in the heater/filter cycle and water is flowing from the jets), the first thing you will look for is the Hi-Limit Switch, also referred to as the heater Pool And Spa TV 57,906 views 3:11 How to Move a Hot Tub with Ease. - Duration: 10:45.

Meter should indicate a continuity when clockwise, and an open circuit (no continuity) when counter-clockwise. Hot Tub Heater Won't Turn On I have tested the power to the flow control valve and the voltmeter says there is power there. A defective control, such as a chattering contactor or thermostat, can pulse power rapidly on and off and cause premature failure. This can be checked by inspecting the back of the control box for the wiring diagram.

Hot Tub Won't Heat Up

The pump 1 button and light do not turn on that pump.

There is no additional cost to you for follow up questions.Jerry : Have a good evening, I will be watching for a reply.Jerry : Thanks for using Just Answer!Customer: thank you Hot Tub Not Heating Up Enough or is it stepped down trough a transformer. Hot Tub Heater Reset Button Terminal Connections Symptom Components Associated Cure 16 No water flow; pump motor humming.

High-limit Switch Filter Cartridge Pump Heater element 15 Burnt wires; melted insulation. this content The easiest remedy then would be to replace the pump or motor assembly. Please try again later. Thanks Share this post Link to post Share on other sites ntrprize 0 Newbie Members 0 6 posts Posted September 23, 2007 · Report post Oh yeah, adjusting the preasure Hot Tub Not Heating After Refill

See Equipment Troubleshooting. When you locate it, give it a push, if you feel or hear a click, or you see a heater indicator light come on that wasn't’t on before, then you have Im thinking its the heater element, but can someone point me how to diagnose this? http://swusf.org/hot-tub/hot-tub-heater-not-working.html You can change this preference below.

Excessive scale buildup on the heater element, as a result of poor water balance, can reduce heating efficiency. Hot Tub High Limit Switch Sundance Spas 32,372 views 3:34 Loading more suggestions... Regular maintenance and water quality are important to maintain the perfect balance.

Heater assemblies come in various forms, a common type shown here.

I recently had the circuitHi, I have a 2008 Sundance Marin. I took a cut wheel and cut the outer layer on the relay top off. Share this post Link to post Share on other sites kengorman 0 Spa Savant Members 0 219 posts Posted September 23, 2007 · Report post Hi, I agree with "The Hot Spring Spa Heater Reset Button CAUTION: Electrical repairs can be dangerous, especially around water.

azurepoolsandhottubs 23,967 views 2:38 Ease of Ownership - Sundance Spas - Duration: 3:34. Register a new account Sign in Already have an account? I recently had the circuit board repaired and now the circulation pump stays on all the time. check over here Jerry : Welcome to Just Answer.

Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Pay nothing to your Expert Is there a way to test the power going to the heater when you are getting the FL1 error? I jumpered the terminals that go to the pressure swith and the heater went right on. If your spa is operating as a 110 volt system, then this is what you should be reading on the meter, if it is a 220 volt system, then that is

Anyone have any idea what kind of pressure switch I need? Sign in to make your opinion count. Sign In Sign Up Browse Back Browse Forums Blogs Calendar Staff Online Users Activity Back Activity All Activity Search Fill out my Wufoo form! If your contactor is 120 volts (see coil info on the side of contactor) then this is what you should be reading, the same applies for 220 volts Mentioned above are

Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. TFP Moderator 24' x 52" Round AGP. 2hp/hp SPL Power-Flo 2-speed pump. 200sqft Waterway Cartridge Filter. 45MHP2(3GPD) Stenner Peristaltic Pump Pool School ----- Pool Math ----- TF-Test Kit Reply With Quote Ask an Expert Home Improvement Questions Pool And Spa Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. characters left:

Join the 9 million people who found a smarter way to get Expert helpRecent Hydro Spa questionsHello SirI have a mark III hydro spa hs200m7 It was offHello

Reduced heat Low heat is more often caused by a reduced water flow rather than an electrical problem with the heater itself.