Home > Hot Tub > Hot Tub Pump And Heater Not Working

Hot Tub Pump And Heater Not Working

Contents

Is changing DPI of LED harmful? Two weeks ago i got out of the hot tub and my girlfriend unplugged a radio we put in the window and the radio flashed tripping the gfci tripped. There are a number of other possible causes to this problem. To remove an air lock, loosen either fitting on the pump to allow the air in the pipe to escape – water should flow for about 5-10 seconds before retightening. 3. have a peek here

Tweet Share53 Pin110 Share34Shares 197 This Is The Last Hot Tub Manual You Will Ever Need You'll save at least $100 off the bat with this easy-to-follow digital handbook. Replace timer. Step 2 Why Does The Hi Limit Switch Trip?     The #1 reason is filter related. All Rights Reserved.

Hot Tub Troubleshooting Heater

However, if you are not 100% confident in your ability to repair your pump and motor, then there is absolutely nothing wrong with calling in a professional. Spa Guy 20,824 views 8:14 # 37 Why do spa heaters fail? - Duration: 9:12. When there is no resistance, the current is leaving the circuit, known as a "short-circuit". If replacing the thermostat does not correct the problem, call a spa professional.

FIX IT Home Improvement Channel 39,254 views 1:31 Spa Heating Element Replacement Overview - Duration: 2:17. SwimUniversity 58,012 views 5:41 Balboa BP2000 Technical Series - TroubleShooting / Testing the Heater - Duration: 2:54. Subscribe here. Hot Tub High Limit Switch See also Total Lack of Heat section below.

If contacts are damaged, install a suppressor on new relay coil. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! These meters can be acquired at most home centers. If you find power on one side of the thermostat and not the other with the thermostat turned all the way up, the thermostat is either defective, out of calibration, or

Close Yeah, keep it Undo Close This video is unavailable. Hot Tub Not Heating After Refill On mine the cover for the control box is easy to open with a screwdriver. Solution: If hot tub is under-filled, add water to the normal fill line. YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART.

Hot Tub Won't Heat Up

Remove any debris or replace a broken impeller. It breaks the electrical circuit powering the heater element, and the heater shuts down, and will begin to heat until proper water flow is established. Hot Tub Troubleshooting Heater EVNautilus 3,323,183 views 5:15 Hot Spring Spas Ozone Mainenance - Duration: 3:52. Hot Tub Won't Heat Up All The Way Can't thank you enough for the great service and fair prices too." M.

Please remember that water and electricity DO NOT MIX. navigate here this sounds like an electrical problem and I would advise hiring a professional. If it does not turn the heater on, replace it. If the hi limit switch is not the problem, follow the instructions below. Hot Tub Heater Reset Button

If the heater draws amperage, the light is broken and needs replacement in order to indicate power to the heater. (No harm will come to the pack if the light does Similar to the Flo error, there are a number of other possible causes to this problem. The next best location is under the insulated cap of a flo-thru manifold. Check This Out Still, sometimes things go wrong, and when you work as hard as the hot tub pump and motor, it is understandable.

May need to get it replaced. Hot Tub Overheating Troubleshooting Which is why it's important to learn some hot tub pump troubleshooting. Mine has 2 breakers in the sub panel, one for the heater and one for the pumps and electronics.

Usually, each tripper on the timer is good for only 30 minutes of low speed operation, however this will vary from unit to unit (some are good for 15 minutes).

You would need to replace it. Is the timer in control (if so, was pack run long enough?) Are all wires in place? What could be causing this Ken Johnson I overfilled my tub the other day. My Hot Tub Won't Turn On A Spa Technician is here to assist: (800) 823-3638 Monday - Friday 6:00 AM to 5:00 PM Pacific Consumer Reviews EasyPak Spa Controls "It's just like the name

Your hot tub pump pulls water from the tub passing it through the filter and the heater and then back through the jets. Is the filter cartridge dirty? (remove if in doubt) Are the jets wide open? Pump Air Switch Pump Motor Symptom Components Associated Cure 7 Continuous high speed; both speeds at once. this contact form If removing the filter didn't solve the problem, then the pressure switch should be replaced.

But in the last 3 days everytime you turn the Jets on and it runs for 10 minutes it pops the main breaker in the house. ehowathomechannel 126,788 views 3:08 Replacing the Heater on your Hot Tub with Wayne Hitchcock - Duration: 6:56. Is the pack set for timer operation? (See Timer Trouble Section.) Hi Speed Pump Does Not Function Check each of the things under Low Speed Pump Does Not Function except the Is the bib fitting tight?

You should see approx. 9-11 ohms of resistance if it is good, maximum resistance if bad. If you hear the "click" and the contactor will not close, check (with your volt meter) to see that the power is found at both terminals on the thermostat. If no power, check the wire leading to the switch for continuity and replace as needed. Loading...

I resoldered it and honestly it isn't a good thing to do I know. If the "click" is still not heard, replace the thermostat. If you have just finished draining and cleaning your hot tub, you may have too much air in the system. If for any reason one of these components fail then the required voltage to the coil will be jeopardized and the contactor will not close in order to send power to

Lastly I don't think the gfci is related I just think it's bad timing. It's nearly impossible to judge someones skill level based on their fist question on the site, so they typically get the "get help" answer/warning when asking a question involving electrical, plumbing,