Home > Hot Tub > Hot Tub Pump 1 Not Working

Hot Tub Pump 1 Not Working

Contents

Forgot your password? Check for voltage coming in an out of the switch, or for mechanical air switches, check that the device is not clogged with debris or insects, and that the air hose It always sounds real quiet, but surely this 4 minute priming mode is somehow getting the pump ready to turn on, right?  Nope - actually, those are just 4 wasted minutes Fill spa to the middle of the skimmer opening. Source

I was able to locate the drain plug on my spa and let enough air out to make the pump actually pump water again! Do not use the lock ring for this, just the lid. What could have happened? This air pocket or air lock needs to be purged from the plumbing so the pump can function normally. https://www.swimuniversity.com/troubleshoot-a-hot-tub-pump-and-motor/

Hot Tub Pump Wont Turn On

Anyone else on this thread have any advice? Turn the spa on and the pump on high. In most cases, it simply because the hot tub needs a good cleaning. water was low but not that low.

CourtDude RVA 86,779 views 3:02 How to deal with a flow reading on your hot tub - Duration: 4:24. By now u probably fixed it but I felt like answering because Matt's go to answer is call a professional. You can test it with an old style dial multimeter or you can just try a new one. 2 Speed Spa Pump Troubleshooting So if its not the relay(which I hope that I checked it right) I would say its the board.

http://www.spadepot.com/Spa-Troubleshooting-W29.aspx SpaCyclopedia Contact CHECK OUT 0 Your cart is empty.Continue shopping to add items to your cart. Hot tubs with these readouts will display an error code when something is wrong or malfunctioning. Bill Walker I just bought a Viking Spas Legacy 2 hot tub about a month ago. Take the lid and push it into place, and then immediately take it off again.

Sign in to make your opinion count. Hot Tub Jets Not Working On One Side If this were truly the problem, it would have fixed it more than allowing to run for just a moment or two (obviously). Solution: Place cover on hot tub and allow it to heat up. It is an electrical issue.

Hot Tub Motor Won't Start

more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Science

There's no water in it, so don't go inside and make a sandwich. Hot Tub Pump Wont Turn On But when I push the jets button, it kicks the breaker. Hot Tub Circulation Pump Not Working softcellelectrical 116,419 views 9:12 *Pressure switch diagnosis.mov - Duration: 3:41.

First, if you are pushing an air switch button, check that the air hose is not crimped or disconnected. this contact form Not sure what to try next. Could be the pump if there isn't a problem. kathy LYONS my topside control is showing 111 degrees , the water is 101 & its showing error code HE Ralph Sampson Sorry for the delay. Hot Tub Pump Just Hums

With power off, make sure that the connections are tight, and the terminals are not rusty or corroded. HELP!!!! With a little luck, the next thing you hear will be bubbles coming from your jets followed by a fully primed pump. have a peek here To remove an air lock, loosen either fitting on the pump to allow the air in the pipe to escape – water should flow for about 5-10 seconds before retightening. 3.

Hot Tub Blogs should do this more often - These are our most Frequently Asked Questions about spa pump repair. Hot Tub Air Lock Symptoms If you have even the slightest doubt, call a spa technician or electrician before proceeding. Everything froze.

If one has an air pocket, then the pump can be started and stopped several times in a row (by pushing jet button) in order to try to clear the air

If you also can let me know what is the date built of the spa this could help me answer your inquiry. Plug the motor only back into the pack and see if it activates without the wet end. Apologies if this is already written up somewhere or misplaced. Hot Tub Pump Making Noise The pump sounds fine, but there's no water moving.

Its very odd. Maybe it looks a little something like this: [attachment=0:12fija01]air relief.JPG[/attachment:12fija01] The red arrows point to unions, the blue arrow points to where there may or may not be a drain plug. No or Low Water Flow Other problems that can contribute to no flow or low flow from the water pump is that the impeller is frozen or stuck, or even broken.  Check This Out Working...

All of these error codes reflect back to the possibility of trapped air in the system. Pump 1 doesn't work still. Can you access the equipment? Home Pool School Forum FAQ Forum Actions Mark Forums Read Quick Links View Site Leaders PoolMath Rules What's New?

Marie leopold Thank you…I have someone coming out Thursday so hopefully it will be something simple! Thanks for your time. If water is dripping or spraying from where the union connects, the PVC threads may have shrunk (from running pump without water), or the threads may be loose and simply need These meters can be acquired at most home centers.

Secure the motor shaft. Still, sometimes things go wrong, and when you work as hard as the hot tub pump and motor, it is understandable. DO NOT DISCONNECT IT COMPLETELY. Here is What You Need to Know The Jet Set - Identifying and Replacing Bathtub & Spa Jets Hot Tub Supplies Need discount hot tub parts ?

HotTubsByArcticSpas 38,078 views 3:41 My hot tub pump turns on but nothing happens - Spa pump airlock - Duration: 1:27. If you’ve unplugged all three components and the breaker still trips, it’s likely the heater element. COOL = Spa water is more than 20° F cooler than the temperature set point. Add to Want to watch this again later?