Home > Hot Tub > Hot Tub Not Working

Hot Tub Not Working


Have used chemicals changed filters and my water is still dirty looking and cloudy! You must be logged in to post a comment. softcellelectrical 116,419 views 9:12 dream maker spa fix bad relays - Duration: 6:15. What else will trip the breaker imediately?

The pump has to be running for your spa to heat, so if the pump does not come on the problem may be with pump itself. Ralph I asked for help and even though u felt it should be left to a professional, thank u for ur response. Voltage variation, of greater than 10% can trip breakers or prevent operation. Broken Pump Impeller It's not usually the cause of a hot tub not working, but in rare cases of a broken spa pump impeller, the motor will start and sound fine,

Hot Tub Display Not Working

There are two 250v 30a fuses, should I replace those? Working... Spa Jets can also become clogged, but it doesn't happen very often. But it will be replaced as soon as April gets here.

I replaced them and it worked a little bit then it tripped again. COOL = Spa water is more than 20┬░ F cooler than the temperature set point. You may find it easier to manipulate the jet adjustment while the pump is off, but should not be necessary. Hot Tub Not Heating Troubleshooting Make sure the batteries are fresh in the meter to insure you get accurate readings.

Shouldn't they trip first? If you have a Printed Circuit Board in your control box click here for more information. Powered by vBulletin™ Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. check this link right here now A noisy motor is another spa pump problem, caused by worn bearings inside the motor.

Now I've pulled the board and have to get a new relay and solder it on. Hot Tub Heater Reset Button When tightening the union, don't over tighten, and be aware of the o-ring and careful that it hasn't come out of position. Other flow problems will be more severe - broken pump impeller, broken valves, or clogged pipes or spa jets. I went back outside and did all 4 of those breakers and then tried again to follow the line that goes inside the top of the garage directly to the meter.

How To Fix A Hot Tub That Won't Turn On

Sometimes, these valves will vibrate into a closed position, especially slice valves used on many spas. http://blog.intheswim.com/hot-tub-not-working-help/ But in the last 3 days everytime you turn the Jets on and it runs for 10 minutes it pops the main breaker in the house. Hot Tub Display Not Working Besides a dirty filter, be sure that other things aren't clogging the works - some floating item sucked into the skimmer or plastic film or heavy paper sucked over the drain Hot Tub Pump Troubleshooting Lot of learning on this project.

This is the important first question, but it's really many questions. My Hot Tub is Displaying an Error Code Modern hot tubs with electronic controls feature spa-side keypads with digital readouts. Leave a Reply Click here to cancel reply. I did just replace my circ pump three weeks ago. Hot Tub Pump Wont Turn On

Check that the valves inside the cabinet are open. Did it all work before without tripping the breaker? If there is voltage, your pump is faulty and needs to be replaced. Spa Cover needs to be replaced.

I can't seem to find the leak in my spa. Hot Tub Control Panel Blank I can't safely advise you to do anything with your tub in this condition. Spacare.com 888-772-9887 Technical Assistance 405-622-4950 0 Item(s) | Total: $0 Home Shop SpaCare.com Spa Part Index Circuit Board Repair Spa Covers Spa & Hot Tub Covers Spa Cover Lifts

From hot tub leaks to control pad error codes, trouble-shooting your own hot tub problems can seem like a daunting task.

May need to get it replaced. Circuit boards also will fail eventually, like every other electromechanical device on a spa or hot tub. On this type of spa heater, you can test the element, high limit and pressure switch for resistance, as measured in Ohms. Hot Tub Motor Won't Start Solution: If there is no water flow, check the voltage going to the pump.

A Hot Tub without heat, is … cold! THERMOSTAT: ┬áThe thermostat is the dial that you turn to crank up the heat. If I had to describe it sounds like it's sucking Air and singing at the same time. Faulty Wiring Incoming wires can be damaged from heat or rodents, or you may have loose connections, or wires touching each other.

Do not use spa when temperature is flashing or the OH message is displayed. Air valves will add volume to the water, and are often surface knobs that can be turned to open or close the air intake line. I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. GFCI tripped.

Spa heater elements burn out very quickly if operated without cooling water surrounding it. We used the hot tub again last night and every time we turn on the jets, that breaker in the 3rd box trips! Electronic Equipment and Computers Electrical - AC & DC Help please? Looked up how to tell if a relay is good or bad.

What to do when your jets do not flow water Sitemap Contact Us 0 @ US $0.00 Menu Home Hot Tub Tips Shipping Contact Us Wish List View Like, is the pump "Air-Locked"? Use any of the information contained in this article at your own risk. Please be very careful!

I resoldered it and honestly it isn't a good thing to do I know. Sign in to make your opinion count. Wondering what your spa is trying to tell you? A voltmeter can be used to test the transformer output, to see that it's within 10% of the rated output voltage, which is normally printed right on the transformer.

Bummer but I don't think I can replace it myself and it looks pretty pricey too. Daniel Lara Hot Tub Works Tags: Hot Tub Repair, Spa Repair This entry was posted on Thursday, July 31st, 2014 at 12:24 pm and is filed under Spa Parts. He should stop being so helpful. Please try again later.

All rights reserved.