Home > Hot Tub > Hot Tub Motors Not Working

Hot Tub Motors Not Working

Contents

Effective spa system electrical troubleshooting usually requires a multimeter for measuring voltage and resistance (ohms). This can reduce the amount of time your hot tub is down for repairs while saving you money at the same time. Hot Tub Maintenance: How to Winterize Your Hot Tub An essential part of hot tub maintenance is winterizing each summer. It says, motor connections to drive should be verified.

Take the back cover off and see if there is any visible damage to the wires coming into the motor. Maybe the capacitor on the pump went out? Replacing a spa pump complete is less complicated when you replace with an exact duplicate pump. Second, if the noise is a low pitched, grumbling noise, the pump could be starved for water. find more

Hot Tub Motor Won't Start

For a hook-up to the circuit box of under 50', pumps of up to 2HP wired for 230V need No. 14 size wire, For pumps wired for 115V, the wire size Browse other questions tagged pump hot-tub or ask your own question. Hopefully you were able to solve your air lock problem by purging air from the system. First, check to make sure none of the electrical circuits have been tripped because of electrical problems.

Threads and overall size can vary greatly. And I know my husband has replaced the motor once during that time, wired the same way. Sandra Posted: 07/29/2016 14:23 PM I went to turn the pool pump motor on. Hot Tub Motor Hums But Won't Start Broken Pump Impeller It's not usually the cause of a hot tub not working, but in rare cases of a broken spa pump impeller, the motor will start and sound fine,

Eventually, all cartridge filters will need to be replaced. Hot Tub Circulation Pump Not Working Sign in to add this to Watch Later Add to Loading playlists... See our guide on "How To Replace a Pool Pump Capacitor". http://www.hottubworks.com/Troubleshooting/Pumps.php It's been running this way for the 16 years we've lived here.

No Water Flow Disengage power. No High Speed On Spa Pump Newer spas are circuit board controlled, with equipment like the blower, heater and pump run through relays and clipped plugs. But when he said the motor needed to be replaced, I didn't question. Look for any drips on the union or valve(s) in front of the pump to locate an air leak.

Hot Tub Circulation Pump Not Working

See if you have power coming to the motor. http://www.spadepot.com/Spa-Troubleshooting-W29.aspx Is it dying a slow death? Hot Tub Motor Won't Start Disconnect the plumbing from the the inlet and outlet. Hot Tub Pump Just Hums Davy Merino InTheSwim Blog Editor Posted in How To Pool Blog Posts Tagged Hot Tub Troubles, hot tubs, Spa Repair, spas permalink Post navigation ← Black Friday Pool Supply Clearance

Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... In some spa systems, when you completely drain the spa, air gets trapped in the pipes and equipment. In most cases you can replace a wet end without unbolting and unwiring the motor. Air leaks on spa pumps will draw air into the pump when the pump is on, and will leak water when the pump is off. 2 Speed Spa Pump Troubleshooting

All valves are open, and no air lock exists. Spa pump motor bearings can be replaced, a new motor can be installed, or installing an entire pump and motor will fix a noisy motor. It suspect it's over heating given the symptom. Add to Want to watch this again later?

If the motor doesn’t work, turn the thermostat and timer completely clockwise. Spa Pump Replacement any suggestions? Closed Valves This happens more often than you think, especially when the spa or hot tub is used by several groups of people, messing with things.

A lot of times, this is what folks really mean when they say their spa is not working.

Fourth, the mechanical switch in the back of the motor could be stuck in the high position, due to broken parts or insect infestation. If you hear air escaping, you have released the airlock. Blower Air Switch Blower Motor 9 Continuous blower. 2 Speed Spa Pump Wiring Diagram Older hot tubs use a flow switch or pressure switch to detect proper water pressure inside the heater manifold, while newer spas have sensors built right into the heater that monitor

Pump display says Drive ERROR! Inyopools Posted: 08/01/2016 0:13 AM Inyo Product Specialist Sandra - Check to see if your timer is working. Are any error codes displayed, like OH for overheat or FLO for flow rate? Check the union in front of the pump, and look for any water leaks when the pump shuts off.

Check your supply voltage. If there’s no power here, then there’s probably an inside wiring problem. If it's stuck, check that the impeller is not jammed with debris. If you hear clicking or feel a vibration or if it starts slow or not at all, replace the pump/motor assembly.

Tighten the union and retry your jets to see if they will work. Make sure to bleed all of the air out of the system before starting it again. Finally, a short in the circuit, from damaged or grounded wires, could keep a hot tub from working. Fourth, is the water level high enough?

Inyopools Posted: 08/29/2016 13:20 PM Inyo Product Specialist Nut 3 - It sounds like the start capacitor on your motor has failed. My question is this- is there a seal or o-ring in that joint that can be replaced or why is water getting in there? No Power Check the main circuit breaker for the spa, and any secondary disconnect boxes, and attached GFCI outlets - to be sure everything is in the ‘On' position, and not Other hot tub tools include jet removal tools, PVC glue and primer, a hack saw for cutting pipe that needs to be re-glued or repaired, Phillips head screwdriver for opening the

Other than that, 14 years is a very good life for a motor.