Home > Hot Tub > Hot Tub Jets Not Working

Hot Tub Jets Not Working

Contents

I can leave it on high for only a split second, then back to low (circulate) and it works just fine until the next time it tries to automatically circulate. It works ok for the normal filtration cycle. admin July 24, 2012 at 12:44 pm Thanks Diana,I am glad that we could help you out with that and thank you very much for taking the time to post about We are leaving for a 10 day vacation in the morning and I was in a panic knowing temps will drop in the 20's at night while we are gone. http://swusf.org/hot-tub/hot-tub-jets-are-not-working.html

About Contact Advertise Privacy Terms Register Help Remember Me? Always do this with the power off and be ready to close them quickly because water will spray out with the air. What to do? With the orifice tees set back inside the wall the length of the pipe between the orifice and the front eyeball can vary greatly. https://www.swimuniversity.com/5-common-hot-tub-issues-solutions/

Hot Tub Jets Won't Turn On

If there is voltage, your pump is faulty and needs to be replaced. I loosened the union at the pump, the air escaped and problem solved. Does it have a lid with an o-ring that gets clamped down on top of it? What could have happened?

You're so thorough at draining your spa that you evacuate every elbow, every little 1/2" line, and every piece of equipment until you know there's not a drop of moisture in Most often this will be caused by a leaking shaft seal, or it could happen from old age. But it's definitely getting worse. In Ground Spa Jets Not Working And about the heater and chasing the line to find the problem.

It sounded like there's air, bubbles or debris trapped in there. Rating is available when the video has been rented. Its very odd. Not a good option if you're going to leave it for a long time, but if you're doing a simple drain and refill close the valves first and you'll always have

Any suggestions? Hot Tub Pump Not Working Go find the plunger. Have used chemicals changed filters and my water is still dirty looking and cloudy! February 15th, 2016 by Daniel Lara It's a common spa question that we get asked all the time.

Half Of Hot Tub Jets Not Working

scott May 15, 2016 Reply Hello, I have bubbles, I have water coming out the jets. Professional help is normally required if replacing the pump does not remedy the problem. Hot Tub Jets Won't Turn On The heat light is off and the thermostat is set lower than the water temperature. Hot Tub Jets Weak Plugged Orifice – a small obstruction can get lodged it the orifice obstructing the water flow.

Watch Queue Queue __count__/__total__ Find out whyClose How To Fix the Air Lock on Your Hot Tub Pump | Arctic Spas HotTubsByArcticSpas SubscribeSubscribedUnsubscribe796796 Loading... this contact form Turn the spa off, clamp the lid in place, spa back on, pump on high and you should be in business. They don't run, hum, get warm….nothing. View our Privacy Policy here. Hot Tub Air Lock Symptoms

If all else fails contact your local Spa Support Desk to book a diagnostic and repair of your Spa. Jason Hughes 736,888 views 7:55 testing and replacing or servicing a hot tub or pool recirculating pump - Duration: 8:06. BigMike So far I replaced the rocker switch. have a peek here A hard water problem should never arise in reality since a test of your water supply will have indicated that the tub required the water to be treated.

Anybody know what the issue might be???!!!! Bathtub Jets Not Working If so, remember to take the lid off next time before you refill it. There could be a few things preventing your jets from pumping water.

And it seems to me it might be the problem after tracking every wire.

some have speakers and subwoofers and the one i have wont work i have tryed many types of i-pods and mp-3 players, the wires are all hooked up, i also would just please send that to my e-mail Diana July 24, 2012 at 12:32 pm Frustrated with an air lock and unable to loosen the union nut so I tried your burping It probably isn't heating due to lack of waterflow. Jacuzzi Jets Not Working Your heater burned up from being exhausted from running with the top off.

It will not filter the water, doesn't look good to guests, and will probably stop you from putting the cover on properly. Solution: If there is no water flow, check the voltage going to the pump. Heat problems Spa water does not get hot Spa overheats Jet problems Jets keep popping out Jets won't rotate Jet insert doesn't spin Water pressure problems Low water pressure throughout spa http://swusf.org/hot-tub/hot-springs-hot-tub-jets-not-working.html Maybe it looks a little something like this: [attachment=0:12fija01]air relief.JPG[/attachment:12fija01] The red arrows point to unions, the blue arrow points to where there may or may not be a drain plug.

Sign in to make your opinion count. What could be causing this Ken Johnson I overfilled my tub the other day. The wiring and equipment described in this article represent a typical spa pack. Each union and drain plug represents a spot in the equipment where we can bleed the air from.

Ralph Sampson GFCI on a hot tub is not something to experiment with. You should hear air or see water coming from it once it's loose. Ralph Sampson Yeah. You're so thorough at draining your spa that you evacuate every elbow, every little 1/2" line, and every piece of equipment until you know there's not a drop of moisture in