Home > Hot Tub > Hot Tub Jets Not Working Properly

Hot Tub Jets Not Working Properly

Contents

Giving me a headache lol! The neighboring jets will still be drawing a suction on those air lines. Results 1 to 16 of 16 Thread: Jets not working after fresh fill? Low water will allow the skimmer to suck air, and cause the pump to lose prime. http://swusf.org/hot-tub/hot-tub-jets-are-not-working.html

The first thing you should check is the water level of your hot tub. It comes on for it's four cleaning cycles and FLO comes back on. If your question was not answered here, feel free to post a comment below, or call our helpful spa tech support personnel at  800-770-0292. The jets never really seemed to work great but they worked. https://www.swimuniversity.com/5-common-hot-tub-issues-solutions/

Hot Tub Jets Won't Turn On

I heard concerns that the impellor may be damaged so it doesnt push enough for all the jets but i would expect they would atleast bubble a little rather then not It probably isn't heating due to lack of waterflow. With power off, make sure that the connections are tight, and the terminals are not rusty or corroded. I have a flo-master pump (230volt)(8.5amp)(1725/3450rpm).

One preventitive method I talked about in my last post on spa start-up involved putting the hose into the filter well as you re-fill the tub allowing water to fill the The jets aren't working! Also the power seems to go off sometime all together and the gfci box has tripped a few times but will reset and I can usually get things going again…But The Some Hot Tub Jets Not Working Hope this saves somebody a service call!

Turn the spa on and the pump on high. Hot Tub Pump Not Working This water and air mixture then flows out of the front giving us the jet action we are all familiar.

What goes wrong with Spa jets? That depends. Now tighten it up and let's do this thing for real.

It will not filter the water, doesn't look good to guests, and will probably stop you from putting the cover on properly. Bathtub Jets Not Working Checked all the peripherals. Insect or ant infestation could also prevent the switch from operating correctly. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...

Hot Tub Pump Not Working

Nigel October 31, 2016 Reply Mike check that your filter is not soiled. check this link right here now If the cable is good try a new panel. Hot Tub Jets Won't Turn On Some tubs have a valve on the top to switch jets between one half of the tub and the other, or middle for all jets. Half Of Hot Tub Jets Not Working All up in your equipment.

Looked up how to tell if a relay is good or bad. http://swusf.org/hot-tub/hot-springs-hot-tub-jets-not-working.html That being said, if you do like to take care of your own equipment, then this guide is the best place for you to be to get started on your hot Tacticalterry Do u have two pumps? A: When you hit the switch or button, and you don't hear your spa pump come on, there are a few things simple things you can try. Hot Tub Air Lock Symptoms

Can't access the equipment? Great write-up. I ran it without filter and it ran for hours no problem. Check This Out Once the water gets going put the filter back in place and turn the pump on high to purge the remaining air.

Once the water gets going put the filter back in place and turn the pump on high to purge the remaining air. Hot Tub Jets Weak My GFCI is Tripping If your GFCI is tripping, it could be due to a bad heater element, pump, blower or ozonator. After bleeding, try turning the power on again and see if the jets work.

This person is right about the air being in the way of the pump pumping water.

Marie leopold I just purchased an older hot tub from a friend. If you have insufficient water input it can mean that you have a dirty filter cartridge, an obstruction in the pump impeller, or even an undersized pump for the amount of Sometimes this will cause the surrounding jets to suck water through the air line backwards through the plugged jet, causing the plugged jet to be pulling water into the eyeball instead In Ground Spa Jets Not Working It should be a quarter turn past hand tight.-Jay Tracey July 6, 2016 at 11:18 pm We just filled our hot tub and the jets were working at first and now

Anybody know what the issue might be???!!!! Jet malfunctions usually lead to weak jets or jets with no air in them at all, but they can also lead to water shooting out of the air controls or a Bill Walker I just bought a Viking Spas Legacy 2 hot tub about a month ago. this contact form Now I've pulled the board and have to get a new relay and solder it on.

None of the breakers have tripped and the fuses all appear intact. Your heater burned up from being exhausted from running with the top off. And it seems to me it might be the problem after tracking every wire. I hope that this FAQ of Hot Tub pump problems has been helpful to you.

Hot Tub Blogs should do this more often - These are our most Frequently Asked Questions about spa pump repair. SnA or SnB = This means that sensor A or sensor B is bad or has a poor connection to the circuit board. Matt Giovanisci Perhaps a bad thermostat. Ralph Sampson You are cleaning it incorrectly.

It is unlikely that both pumps would be siezed but I suppose it is possible. Does it have a lid with an o-ring that gets clamped down on top of it? If we reduce the size of a pipe with fluid moving through it, the velocity (speed) of the water increases, but the pressure in the pipe decreases. Randy Simmons Yes.

If you are in a freezing climate check the line that comes off the discharge side of the pump. It works ok for the normal filtration cycle. The spa is at a temperature above 108° F. This is most often caused by hard water.

Nigel September 08, 2016 Reply Harrison what make and model spa do you have?