Home > Hot Tub > Hot Tub Controls Not Working

Hot Tub Controls Not Working

Contents

We repair Hot Tub circuit boards! Comments What Is a Hot Tub Blower? Sign in to make your opinion count. Repair of electronic spa sides is usually accomplished by replacement.

YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART. Examine the panel to see if any moisture is inside the display. My touch pad is blank?If so, check power is turned on at the power point, the isolation switch (if spa is hardwired), then the main switch board to your house with If all else fails contact your local Sundance Spas Support Desk to book a diagnostic and repair of your Sundance spa. http://www.doityourself.com/stry/troubleshooting-hot-tub-control-panel-problems

Hot Tub Control Panel Blank

Lot of learning on this project. Dry fire of heater from ice that may have still been in the system blocking the lines? Pump Seal Heater Manifold Valves Plumbing Jets Spa Shell All About Spa Packs Frequently Asked Spa Repair Questions Spa Anatomy Need help or additional information? If you do not get these readings, then either a fuse is blown or the transformer is faulty.

Dry-top, Splash-top, and Open snorkels. There well could be other things wrong, but doing this step is a good start. Put filter in it ran about 6 minutes. My Hot Tub Won't Turn On The 10/24/2016 10/24/2016 JACUSTOMER-x0uwnnmp- I have a leisure bay spa with a 501s control panel.

The spa lit up and came on. Temperature The button that makes a hot tub a HOT tub! No thanks Try it free Find out whyClose # 36 Why doesn't my hot tub work softcellelectrical SubscribeSubscribedUnsubscribe5,6815K Loading...

If you do not understand what I just said you need to read, not look on blogs.

The Numbers are Missing or Blank Make sure your connection is clean. Hot Tub Control Panel Codes Sign in 11 Loading... Turns out the transformer blew out two legs. Pump Air Switch Pump Motor Contactor/Relay 8 No blower.

Top Side Control Panel Not Working

Re: Control Panel not Working « Reply #2 on: August 25, 2004, 12:58:18 PM » I had the power turned off all night, went out first thing this morning with the https://spacare.com/circuitboardtroubleshooting.aspx Each function will echo from the circuit board to the LCD/LED in a corresponding manner. Hot Tub Control Panel Blank All information is provided "AS IS." Website operating problems contact [email protected] No Display On Hot Tub rpmtechtv 17,830 views 6:15 How to Move a Hot Tub with Ease. - Duration: 10:45.

Sign in to add this video to a playlist. The perfect fragrance for a family party! But it will be replaced as soon as April gets here. If the new topside works, replace the old unit. Hot Tub Lights Not Working

Hot tubs with these readouts will display an error code when something is wrong or malfunctioning. Disconnect this harness and your remote panel will be deactivated but you should still have control through your main panel. We will not be held liable for any injuries that may result from the troubleshooting or installation of any electrical components in your hot tub spa unit.Safety is key when servicing Gently remove the topside control panel.

Can't thank you enough for the great service and fair prices too." M. Hot Tub Troubleshooting No Power If it still does'nt work you may have a bad main control panel, bad connection at the PWA or a bad PWA. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next.

Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading...

Loading... You may freely link to this site, and use it for non-commercial use subject to our terms of use. Thermostat Heater Contactor/Relay Spa Side Control Symptom Components Associated Cure 4 No low speed pump; no ozonator function. Hot Tub Control Panel Locked Get a comprehensive list of hot tub error codes and what they mean. 4.

Click On A Problem Below To See The Solution: - My 220 Volt Spa No Longer Gets Hot - I'm Getting Error Codes Or Blinking Dots - The GFCI Trips When Working... Readings should be taken at the terminal block on the circuit board. Replies September 08, 2013 Reply Derek it sounds like you may have a bad remote panel.

The readings above are normal so please do not send your circuit board in for repair with the above readings. 4. You can solder a t'former with no issues. Safety first. If the light did not come on, then the circuit board will need to be sent in for repair or replaced.

The 5 Most Common Error Codes and What They Mean Flo or FLC = Improper flow or pressure switch malfunction. These controls are susceptible to moisture, you can turn of power, disconnect the topside from the control board, remove the topside, and use a hair dryer to blow warm air in characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 426 12367265 http://www.spadepot.com/Spa-Troubleshooting-W29.aspx SpaCyclopedia Contact CHECK OUT 0 Your cart is empty.Continue shopping to add If you can't sort the problem then check topside is pugged into the circuit board correctly (turn spa off) - if it is then remove decal and check buttons - if

My Pump is Making Loud Noises If your pump is louder than it used to be, the bearings in the motor are going out and soon the motor will seize. Sunplay Company ›About Us ›Blog ›Brands ›Our Utah Store ›Sponsorship Program Resources and Policies ›Image Copyright ›Pool Volume Calculator ›Privacy Policy ›Shipping Policy ›Terms & Conditions Sign up for emails Subscribe the lights come when the power is turned on and i cannot turn them off, nor can i raise or lower temp, turn on pumps...etcit is under warranty and i have Now the jets have stopped working.

Here are five tips to make cleaning a more efficient process. Published on Apr 7, 2012# 36 Several basic reasons why hot tubs stop working and ways to prolong their life. Do not use spa when temperature is flashing or the OH message is displayed. What could have happened?

Try disconnecting the remote panel from the sensor loom inside the skirt panel. All rights reserved.