Home > Hot Tub > Hot Tub Controller Not Working

Hot Tub Controller Not Working

Contents

Randy Simmons Is there a blower on the spa? The heater going bad or me tryin to turn it on to diagnose it cause the relay to begin tripping with great ease. Back to top Pool Care Hot Tub Care Resources Search 5 Common Hot Tub Issues and Solutions Download our FREE guides and receive new posts every week. I'm very impressed by the support offered here - great advise which i'm very grateful for.

Both mean the same thing and will be troubleshot the same. The topside if going blank, is most likely going to need replaced anyway, and it will be easier to trouble shoot the rest of the issues with the topside working. He should stop being so helpful. Cheers Bobby Speeks October 02, 2015 Reply Just purchased a used Sundance spa an the display panel continues to blink…..I can turn the heat up an down, turn the light on…..but

Hot Tub Control Panel Blank

Randy Simmons I have a 0ld Jacuzzi Z150 Spa. You should see 220 volts on your volt meter - note that measuring from each wire to ground will not give an accurate reading). You must be logged in to post a comment. If it is not then there may be an issue with the pressure switch (it may be defective).

Dead Control Panel If part of the control panel is dead or the whole panel is frozen, you will want to see if the problem is the circuit board or the Each function will echo from the circuit board to the LCD/LED in a corresponding manner. Nigel October 03, 2015 Reply Bobby what is the make and model of your spa and what is the date built. Hot Tub Control Panel Codes Or are you trying to get it working for the first time?

kathy LYONS my topside control is showing 111 degrees , the water is 101 & its showing error code HE Ralph Sampson Sorry for the delay. Top Side Control Panel Not Working The control panel wont do This answer was rated: ★ ★ ★ ★ ★ My vita spa has stopped working. Then try your main control panel button again.

Any suggestions?

Transformers are fairly easy to recognize and are about 1.5″ square, with wire leads attached. My Hot Tub Won't Turn On BigMike So far I replaced the rocker switch. Solution: If there is no water flow, check the voltage going to the pump. CAUTION: Electrical repairs can be dangerous, especially around water.

Top Side Control Panel Not Working

Spa Light Bulb Failure Spa light bulbs don't last forever, and this may be the first thing to check. https://www.poolandspacentre.co.uk/help/hot-tub-topside-spa-control-troubleshooting.html The Main Terminal Block Where The Incoming Power Terminates Has Burned/Melted The Copper Straps Connecting The Board To The Heater Have Burned/Melted One Or More Wires That Connect To The Circuit Hot Tub Control Panel Blank Mon - Fri 9am - 5pm Calls cost 5p plus your phone company's access charge Categories Search Spa Shop Pool Shop Sauna Shop Leisure Shop Search Search You are here: Home No Display On Hot Tub YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART.

Everything froze. The heat light is off and the thermostat is set lower than the water temperature. Dead.The main fuse appears good. Thanks! Hot Tub Lights Not Working

Ask Jerry Your Own Question Jerry, Technician Category: Pool and Spa Satisfied Customers: 3360 Experience: owned and operated spa and pool retail store for 12 yrs 34748161 Type Your Pool and Plug in properly and check to see thay make good connection. Consult an electrician to find the source, if not readily apparent (burnt wires, insects or rodent damage, water). If you DON'T have 220 volts, then you have an issue with the GFCI breaker in the main breaker box.

Looked up how to tell if a relay is good or bad. Hot Tub Troubleshooting No Power The 5 Most Common Error Codes and What They Mean Flo or FLC = Improper flow or pressure switch malfunction. If you push the light button and can hear a small noise, then you do have relays.

Matt Giovanisci Sounds like you have an issue with your pump.

Is it definately the controller and not something to do with the heat? Expert: Jerry replied3 years ago. These controls are susceptible to moisture, you can turn of power, disconnect the topside from the control board, remove the topside, and use a hair dryer to blow warm air in Weather Tempature got below freezing. Hot Tub Control Panel Locked Matt Giovanisci At this point I would just call someone.

Bought new filter, (this is when I found the gfci had tripped earlier in the week) I reset gfci put filter in and went to work. The quickest way to confirm if this is the case is to disconnect both leads from the circuit board supplying power to the heating element. There are two 250v 30a fuses, should I replace those? If so and they are the same swap the cords to see if u still have a flo problem.

Our complete troubleshooting library can be found here. Believe it or not my boyfreind and I are both electronic technicians but I dont know much about hot tubs. Bill Walker I just bought a Viking Spas Legacy 2 hot tub about a month ago. I tried to restart it but it wouldn't work for long it would go into watchdog mode.

Resetting the spa by turning off the power, waiting and turning it back on is likely to resolve the issue. To remove an air lock, loosen either fitting on the pump to allow the air in the pipe to escape – water should flow for about 5-10 seconds before retightening. 3. I replaced them and it worked a little bit then it tripped again. Have you tried this sequence? Ask Your Own Pool and Spa Question Customer: replied3 years ago.

Sign in 55 10 Don't like this video? Frozen water in the Pumps? The fuse is usually located inside the spa pack, possibly next to other fuses. I had looked at that ribbon cable several times before but didn't realize that was where they connected.

but no power to the top control panel display. My touch pad is blank?If so, check power is turned on at the power point, the isolation switch (if spa is hardwired), then the main switch board to your house with If any of these symptoms are present, perform the following: Turn the power off and unplug the panel from the circuit board. or SpaDepot.com customers with accounts enjoy these benefits: Faster checkout Order status & history Easier package tracking Manage addresses Favorites list Exclusive deals CREATE ACCOUNT SHOP AS GUEST All Products

To determine which component is causing the problem, unplug the components one at a time and turn the breaker on. The hot tub is 9 years old now. I can unsubscribe at any time. * Support TypesProblemsQuestions Support TopicsHot TubsAccessoriesControl Panel ErrorsHeat IssuesLeaksLightingOtherStereoWater Flow IssuesPoolsFiltersHeatersLeaksLinersOtherPool StructurePumpsSaltProblemsQuestionsWater CareCloudy WaterGreen WaterHot Tub WaterSalt Water Pools Hot Tubs Bathrooms Service Pool Renovations Leave a Reply Click here to cancel reply.

Touch pad does not respond to touch: Check the panel has not been locked.