Home > Hot Tub > Hot Tub Blowers Not Working

Hot Tub Blowers Not Working

Contents

This would cause the water in the spa to reach temperatures high enough to cause the hi limit switch to trip, disengaging high speed operation (as well as the heater.) If Unless you are a mechanic, you should not get involved in any hands-on maintenance of the motor. Rating is available when the video has been rented. Disconnect the thermostat wire leading to pressure switch before checking thermostat for voltage.

Hot tubs with these readouts will display an error code when something is wrong or malfunctioning. It did come on at the beginning of every filtration cycle, and it was used occasionally for people wanting ultra strong jet power (not me). Spa Guy 6,861 views 25:46 231 videos Play all מוזיקה ישראלית משובחתShelly C Sundance Spas ~240V~ Air Blower Motor Replacement in Your Hot Tub - Duration: 13:31. Tacticalterry So when the top blew off it kept running and burnt the heater out as u stated. http://www.doityourself.com/stry/troubleshooting-hot-tub-blower-problems

Spa Blower Motor Replacement

Pressure switch? DrcJr77 SubscribeSubscribedUnsubscribe1,4071K Loading... Loading...

Have tried everything to fix it. Leak. If not, and the pressure switch is of the type that has a barbed fitting and a hose connecting it to the heater, have the new switch close by and proceed Silencer Air Blower Troubleshooting If you hear the "click" and the contactor will not close, check (with your volt meter) to see that the power is found at both terminals on the thermostat.

Sign in to add this video to a playlist. Hot Tub Blower Works But No Bubbles You turn on your hot tub and nothing happens and then begin to wonder what exactly you are going to do. Each will plug into a socket provided on the control box of many models. http://www.poolandspa.com/page831.htm If it does not activate, go to check #6.

The clock on the timer is rarely going to be bad. What Does A Spa Blower Do Relays vs. The 5 Most Common Error Codes and What They Mean Flo or FLC = Improper flow or pressure switch malfunction. To be sure you have matched them correctly, once the impeller is installed and the pump is running under full load, take an amperage reading while on high speed.

Hot Tub Blower Works But No Bubbles

Do not mix them up. 1-1/2hp impellers must only be used with 1 -1/2hp "full rate" motors (those that have a service factor of 1.0) and 1 hp impellers with 1 https://www.swimuniversity.com/5-common-hot-tub-issues-solutions/ Any suggestions? Spa Blower Motor Replacement To prevent this, you can use a flocculant to coagulate the particles into larger particles the filter can catch before the water is sent back into the pool. How Does A Spa Blower Work This information is not intended to replace or substitute for information contained in equipment owner’s manuals.

A relay coil is always identified as terminals A and B on the relay while the switch terminals are numbered. Watch Queue Queue __count__/__total__ Find out whyClose HowTo: Replace the Air Blower Motor in Your Hot Tub or Spa ~Sundance Altamar SpaDayz SubscribeSubscribedUnsubscribe420420 Loading... If you have power but do not get proper switching action, replace the switch. Avoiding Water Intrusion The most common cause of blower failure is moisture inside the housing. Hot Tub Blower Trips Breaker

Lastly I don't think the gfci is related I just think it's bad timing. Javascript must be enabled for the correct page display Skip to Navigation Skip to Content × Login to DoItYourself Log In with Facebook Username Password Forgot Username or Password? Correct Tech - Duration: 3:58. If you turn it around 1/4 way without hearing the click, your thermostat must be replaced.

The more material used, the larger the surface area available to capture unwanted dirt or debris in the water. Hot Tub Blower Making Noise Now that your new hot tub air blower is installed, go ahead and turn the power back on to your hot tub. To replace it, first shut off the power and then remove the two wires going to it.

That is, if the tripper in front of the arrow is pushed in, and the next several trippers are also pushed in, turning the bypass to have the low speed pump

If insulated properly you should not be able to see the side of either bulb under the cap once the nut is tight. Also, while the impeller is accessible, check the tightness of the impeller on the shaft. My Hot Tub Won’t Heat Sometimes a heating problem is as simple as replacing a heater element, however sometimes the problem can be caused by another component. Spa Blower Check Valve For more information on when and how to replace the sand, contact your pool/spa retailer or service technician.

Don't Have an account? One quarter revolution is equal to a rise of 100. Step 8 Pull the fuse out of the fuse clips. Tip: Parts and labor from motor shops can be very close to the cost of a brand new pump with a warranty, so do yourself a favor and replace the pump

Spa Guy 711 views 4:01 Spa Hot Tub Air Control System.. WARNING: DO NOT LUBRICATE WITH ANYTHING BUT WATER. Matt Giovanisci At this point I would just call someone. The spa lit up and came on.

Troubleshooting Pressure Switches A pressure switch will allow power to pass through it as long as there is a measurable amount of pressure in the cavity to which it is connected. A modern, high quality spa air blower will have a drive motor designed to hold up well in damp conditions, run much quieter than a vacuum cleaner motor, and should have If so and they are the same swap the cords to see if u still have a flo problem. That is, as long as the valves are shut creating a sealed cavity in order to build pressure.

PVC cement is be used on the wet side to prevent water leaks, but tiny air leaks are not a consideration. We have had a few problems…the Jets seem to review rather than run consistently when I turn them on. Once you've enabled Javascript, please refresh this page. Problem Causes Solutions Short filter runs A build up of dirt and other materials in the filter.

On 240v observe contactor or heater relay. If you do believe you can do it, then you must take a few safety precautions first. Other lubrication will allow the seal to spin on the shaft once the pump is turned on. stackz00 150,870 views 8:06 5 Common Hot Tub Issues and Solutions - Duration: 5:41.

A 110 volt pack will only heat on low speed at a rate of 2 to 3 degrees per hour. If you are not confident that you can perform the repair safely, then please call a technician. They are pretty simple units, consisting of a fan motor and a housing.